All Products

Mills War Eagle slot machine

Here is a Miss-O electromechanical pinball by Williams made in 1969.  We purchased this pinball for resale.  We did a complete shop-out...

This Missile Command by Atari had game board problems and monitor issues.  Unfortunately for the customer these two failures did not occur at...

Price is for 1 each.  MJ11015G Transistor PNP Darlington, 120v CE, 30a Picture is for reference only, actual device may differ. Datasheet

Price is for 1 each.  MJ11016G Transistor NPN Darlington, 120v CE, 30a Picture is for reference only, actual device may differ. Datasheet

Transistor MJE3055 Datasheet

Here is a Monopoly Pinball made by Stern in 2001 - 2002. This is a well made game that had proven revenue numbers.  Most ended up in homes, as...

Monte Carlo Pinball by Gottlieb/Premier  1987 01/19/2013 09:38:45  Picked up @ 01/12 02/17/2013 15:53:57  Cleaned and waxed, all new...

Price is for 1 each.  MPSA06 Transistor, NPN 80v CE, 500ma Picture is for reference only, actual device may differ. Datasheet

Price is for 1 each.  MPSA42 Transistor, NPN 300v CE, 200ma Picture is for reference only, actual device may differ. Datasheet

Price is for 1 each.  MPSA56 Transistor, PNP 80v CE, 500ma Datasheet

Price is for 1 each.  MPSA92 Transistor, NPN 45v CE, 200ma, low noise Datasheet

MRF477 RF/HF/VHF Radio output transistor.  TO-220AB package.  1.5 to 30mhz.  40 watt PEP.  Used in many HAM 10 and CB 11 meter...

We have here a Ms Pacman made by Midway in 1982.  We went through the game board, the monitor and rebuilt the control panel with a new overlay...

This repair is on a Ms Pacman game.  This is a typical problem on all the Midway games of the period.   The problem is the edge...

Ms Pacman/Galaga game board, REAL Namco coin operated type.  This is not the HOME model, although it will work in a home game.  It does...

Here is an example of a "Multicade" game that came in with a bad monitor.  These "Multicades" are really just copies of original game software...

Bally Drop Target Bank Reset coil part number NB-26-1900 (3 terminal).  Comes with a 2" sleeve with a 1/2" outside diameter (pn: 03-7068)....

Replace your Gotlieb System 1 game board with this Ni-Wumpf aftermarket product.  Just set the dip switches to your game.

Night Rider pinball by Bally  1977

This repair is on a Nip-It pinball machine made by Bally in 1972.  This game is a bit harder to shop out than most.  It has the fixed hinge...

Hex Machine Screw Nuts with Small pattern 1/4" head.  Size - #6 x 32 turns per inch. Great for small places using a 1/4" nut driver.  Like...

Hex Machine Screw Nuts with Small pattern 1/4" head. Size - #8 x 32 turns per inch. Great for small places using a 1/4" nut driver. Like arcade coin...

Price is for 1 each.  Nylon Screw for mounting TO-220 type transistors.  6x32x1/2"  Atari used these on the power supply boards.

Gottlieb Nylon washer - spacer used on EM machines.  Used on reel mechanisms that have no Disc.  Spacer replaces the printed circuit board...

OPTEK - pn: OPB804 is a replacement optical interrupter used on many William/Bally pinball machines.  It's like a Swiss Army Knife of...

Open Frame Power Supply with  5v @3a, 12v @2a, -12v @.3a outputs.  100 to 240VAC input.  This is  a good replacement for the...

Open Frame Power Supply with  5v @5.5a, 12v @2.5a, -12v @ .5a outputs.  100 to 240VAC input.  This is also a good (Higher Current)...

Open Frame Power Supply with  5v @5.5a, 12v @2.5a, -5v @.5a outputs.  100 to 240VAC input. 

Opto Magnet Bracket Assembly for Williams "No Fear" pinball machine.

Opto Receiver PCB for Stern Pinball ball upkicker.

Opto Transmitter PCB for Stern Pinball upkicker.

Here is an original Pac-Man from Midway that set the standard in the great old days of video games.  This one had a severe water/rust...

This IGT Slot was supposed to be just a simple SRAM clear and bill validator reset service call.  After we changed the battery and did the clear...

Phono Cartridge connector pin assortment kit.  25 peice set. 

Price is for 1 each.  Molex connector pin for .156 housings .  Trifurcon high current type. Bally Note: These are really only needed if you...

Price is for 1 each.  Crimp Terminal Pin for Molex Type Housing .100" or 2.54mm spacing. For Wire size 22 -28 AWG.

Price is for 1 each.  Crimp Terminal Pin for Molex Type Housing .156" and .200" spacing.  For Wire size 22 - 26 AWG.

Price is for 1 each.  Crimp Terminal Pin for Molex Type Housing .156" and .200" spacing.  For Wire size 18 -20 AWG.

This game is called "Pinball".  It was made by Stern in 1977.  This game has two very big issues with the design.   First the...

In-shop pinball repair service.  Just a repair billed by the hour.  Repair a specific problem at your direction.  Warranty only on the...

Bring in your electro-mechanical pinball game that has spinning score reels and bell chimes. Made between 1965 - 1977 (not computer controlled) ....

Bring in your electronic pinball machine (made after 1977) for full service known as a complete "Shop Out" .  By Shop Out, we mean everything...

Pinball switch with 3.1" flat blade

Carbon Steel Pinball - 1 1/16 inches. Standard on most pinball machines since 1950.  High carbon steel.  Scratched or rusted balls will...

Here is a Pinbot pinball machine made by Williams in 1986.  This is one of the great ole pinballs that made a ton of money on the streets. ...

This is a pitch and bat game from 1959 called Pinch-Hitter Deluxe by Williams.  This was a repair only since the machine was just...

This pinball repair of a 1975 Gottlieb "Pioneer" was a 7 day project.  Most of the time I can go through one of this type in 4 days...