All Products

Price is for 1 each.  MPSA56 Transistor, PNP 80v CE, 500ma Datasheet

Price is for 1 each.  MPSA92 Transistor, NPN 45v CE, 200ma, low noise Datasheet

MRF477 RF/HF/VHF Radio output transistor.  TO-220AB package.  1.5 to 30mhz.  40 watt PEP.  Used in many HAM 10 and CB 11 meter...

We have here a Ms Pacman made by Midway in 1982.  We went through the game board, the monitor and rebuilt the control panel with a new overlay...

This repair is on a Ms Pacman game.  This is a typical problem on all the Midway games of the period.   The problem is the edge...

Ms Pacman/Galaga game board, REAL Namco coin operated type.  This is not the HOME model, although it will work in a home game.  It does...

Here is an example of a "Multicade" game that came in with a bad monitor.  These "Multicades" are really just copies of original game software...

Bally Drop Target Bank Reset coil part number NB-26-1900 (3 terminal).  Can also replace the NO-26-1900 (use only the outside 2...

Replace your Gotlieb System 1 game board with this Ni-Wumpf aftermarket product.  Just set the dip switches to your game.

Night Rider pinball by Bally  1977

This repair is on a Nip-It pinball machine made by Bally in 1972.  This game is a bit harder to shop out than most.  It has the fixed hinge...

Price is for 1 each.  Nylon Screw for mounting TO-220 type transistors.  6x32x1/2"  Atari used these on the power supply boards.

OPTEK - pn: OPB804 is a replacement optical interrupter used on many William/Bally pinball machines.  It's like a Swiss Army Knife of...

Open Frame Power Supply with  5v @3a, 12v @2a, -12v @.3a outputs.  100 to 240VAC input.  This is  a good replacement for the...

Open Frame Power Supply with  5v @5.5a, 12v @2.5a, -12v @ .5a outputs.  100 to 240VAC input.  This is also a good (Higher Current)...

Open Frame Power Supply with  5v @5.5a, 12v @2.5a, -5v @.5a outputs.  100 to 240VAC input. 

Opto Receiver PCB for Stern Pinball ball upkicker.

Opto Transmitter PCB for Stern Pinball upkicker.

Here is an original Pac-Man from Midway that set the standard in the great old days of video games.  This one had a severe water/rust...

This IGT Slot was supposed to be just a simple SRAM clear and bill validator reset service call.  After we changed the battery and did the clear...

Phono Cartridge connector pin assortment kit.  25 peice set. 

Price is for 1 each.  Molex connector pin for .156 housings .  Trifurcon high current type. Bally Note: These are really only needed if you...

Price is for 1 each.  Crimp Terminal Pin for Molex Type Housing .100" or 2.54mm spacing. For Wire size 22 -28 AWG.

Price is for 1 each.  Crimp Terminal Pin for Molex Type Housing .156" and .200" spacing.  For Wire size 22 - 26 AWG.

Price is for 1 each.  Crimp Terminal Pin for Molex Type Housing .156" and .200" spacing.  For Wire size 18 -20 AWG.

This game is called "Pinball".  It was made by Stern in 1977.  This game has two very big issues with the design.   First the...

In-shop pinball repair service.  Repair a specific problem at your direction.  Warranty only on the parts replaced and the labor to replace...

Bring in your electro-mechanical (not computer controlled, has spinning score reels) pinball machine (made between 1965 - 1977(older pinballs...

Bring in your electronic pinball machine (made after 1977) for full service known as a complete "Shop Out" .  By Shop Out, we mean everything...

Pinball switch with 3.1" flat blade

Carbon Steel Pinball - 1 1/16 inches. Standard on most pinball machines since 1950.  High carbon steel.  Scratched or rusted balls will...

Here is a Pinbot pinball machine made by Williams in 1986.  This is one of the great ole pinballs that made a ton of money on the streets. ...

This is a pitch and bat game from 1959 called Pinch-Hitter Deluxe by Williams.  This was a repair only since the machine was just...

This pinball repair of a 1975 Gottlieb "Pioneer" was a 7 day project.  Most of the time I can go through one of this type in 4 days...

Here is an example of a repair shop nightmare.  This 1978 Bally Playboy had been sitting in a Texas barn that was not exactly protecting the...

Plunger and Link Assembly,  Bally Pinball.  With fiber link.  For old electro-mechanicals 1975 to 1980 electronic Space...

Flipper plunger and link assembly for Bally/Williams pinballs.  New type with thicker link(1984 - 1998).  Will not work on older pawl that...

Plunger and Link assembly for Williams/Bally pinball machines.   This is the Tapered(thin) version link, 1980 to 1991.

Plunger Fiber Link,  Bally Flipper.  EM and early MPU electronic Pinball.  Link is 9/16" hole to hole. 1 1/8" total length.

Complete flipper plunger link and pawl assembly for Williams Pinball. Left Side.  A-15848-L

Complete flipper plunger link and pawl assembly for Williams Pinball. Right Side.  A-15848-R

Bally "Nyliner" snap in bearing.  For Bally "Linear" motion flipper plunger bracket.  PN: C-537-8  Bally

Contact adjuster-L shaped  Useful on electromechanical pinball machines.

Here is an upright model Pole Position made by Atari in 1983.  This was converted with new eproms to a Pole Position II. These games can be...

Pop Bumper Base - old style Bally/Williams C-115-1, 03-6009-A5 Gottlieb A-10432 Stern/Data East/Sega 545-5195-00

Pop Bumper Body for newer style pinball games.  For Williams, Bally and Stern. Bally/Williams 03-7443-5, Stern/DE/Sega 545-5197-00 

Bumper Body (non pop - no solenoid - no ring)  "Dead Bumper" Bally C114, Gottlieb 25A. Replaces Chicago Coin pn 16510, Gottlieb pn B-10431, and...

Pop Bumper Body - old style, used on many makes and models.  Williams 3A-6008, Bally C114-3, Gottlieb 8997,  Stern(Old)...